450142 *6/ pack *12/ case
450042 *2/ case *4/ load
450152 *2/ load *4/ load
🔆
0
0
0
.57
.46
.39
259
207
176
.09
.29
.56
💧
0
0
0
.56
.45
.38
253
201
173
.88
.85
.16
🍅
0
0
0
.55
.43
.37
248
196
169
.61
.41
.76
🌱
Resin-XS
The No.1 BLOOM BOOSTER for Serious Growers
Improves fruit quality and development: Increases frosting, resin, density and final mass
Aids PGR recovery: Opposes the negative impact of PGRs to dramatically improve final quality e.g. potency, trichomes, color
Free from PGR's
The ideal replacement for “finishers”, PK additives and bloom boosters. Its PK-additive component suites any nutrient regime as it is “pH-neutral” and balanced to ensure optimum flower density
Will NOT cause biofilms, blockages, foaming or odors
Resin-XS ProPowder:
Dissolves fully within minutes even in hard or cold water
Can be added dry to reservoir, or made into highly stable stock solutions for use with auto-dosers
Each batch of FloraMax is manufactured by our in-house chemists and undergoes rigorous quality testing before bottling, ensuring consistent performance and reliable yields from each crop.
Dosage
Liquid: 2-4ml/L (8-15 ml/Gal)
ProPowder: 0.2-0.4g/L (0.8-1.5g/Gal)
Timing: Generally use from bloom week-4 up until harvest. Use the highest rate from week-5. As a stand-alone PK additive/bloom booster/’finisher’, use through entire bloom phase.
FloraMax liquids can be substituted with their powdered version, and vice versa.
Powders can be added dry to reservoir as a dry pre-mix or individually, or made into stock solutions.
Organic Additive — NEVER use in conjunction with chlorines or peroxides
Many plants have glandular trichomes. These are well-known sources of essential oils and resins that have a widespread use in agricultural, pharmaceutical, and cosmetic industries.
Without Resin-XS
With Resin-XS
How to test Resin-XS with an existing nutrient regime?
For any nutrient schedule, Resin-XS replaces all “finishers”, PK additives, bloom boosters or resin enhancers. Generally use Resin-XS at 2m/L (8ml/Gal) from Bloom Week-1 through to harvest and apply at every watering. This dose rate will yield EC 0.3mS, hence you might need to remove an existing PK additive or bloom booster from the schedule to make room for this extra EC. Note, improved yields are usually obtained by increasing usage to 3-4ml/L (11-15ml/Gal) from Bloom Week-5 to 8 (mid to late bloom).
With Resin-XS, within a few weeks you should notice increased frosting, potency, swell and density. Unlike alternative products, Resin-XS runs as clean as salts and contains nil PGRs. It will also offset the negative impact of PGRs – if they are being used.
Should I be adding *extra* PK additives to the FloraMax feeding schedule during bloom?
No, the PK levels (Phosphorous and Potassium) are optimized with Flowering Enhancer (0-5-3), Resin-XS (0-1-4) and the FloraMax base nutrient (Veg-1 or VegaFlora AB). During mid-to-late bloom, we generally recommend using Resin-XS at 3-4ml/L (11-15ml/Gal). For heavy feeders, 4ml/L (15ml/Gal) generally provides significant improvements in mass yield and terpene profile.
'Purified extracted organics' explained
The chemists at FloraMax have been able to deconstruct popular organic ingredients such as kelp, fulvic acid and guano then isolate specific ‘beneficial’ organic molecules. These are then incorporated into our additives in a purified and potent form. Importantly, this enables their concentrations to be optimized for maximum nutrient effect, with no negative side-effects. The result is a range of products that produce unique and tangible results without causing blocked drippers, pH fluctuation, build-up, foaming or odors.
